news
Location: Home ->  news

Name and function of each part of the placement machine


note:
1) Grasp the name of each component and compare it to the actual object of the machine to indicate the name and basic functionality of the component.
2) Which button should be pressed in the event of an emergency, the status of the warning light and the display of the operation display?




note:
a) Unauthorized personnel are strictly prohibited from operating the machine.

b) The operating equipment must be safe first. The machine operator should operate the machine in strict accordance with the operating specifications. Otherwise, the machine may be damaged or compromised.
c) The machine operator should be careful.
Fourth, the name and function of each part of the placement machine
host
1.1 Main power switch: turn main power on or off

1.2 Visual Monitor: Displays images or components obtained by moving the lens and symbol recognition.
1.3 Operation Monitor: Displays the VIOS software screen for machine operation. If an error or problem occurs during the operation, the calibration information will also be displayed on the screen.
1.4 Warning Light: Indicates the working status of the placement machine in green, yellow and red.
Green: The machine is in automatic operation
Yellow: Error (cannot perform return to origin, pick error, identify fault, etc.) or generate an interlock.
Red: The machine is in an emergency stop (press the machine or the YPU stop button).
1.5 Emergency stop button: Press this button to trigger an emergency stop immediately.
2. Head assembly
Work head assembly: Move in the XY direction (or X direction), pick up parts from the feeder and mount them on the PCB.
Movement handle: After releasing the servo controller, you can move in all directions with your hands. This handle is typically used when moving the work head assembly by hand.
3. Visual system
Mobile camera: Used to identify markers or position or coordinate tracking on the PCB.
Single Vision Camera: Used to identify components, primarily components with pins.
Backlight unit: Illuminates the component from the back when it is recognized by a separate vision lens.
Laser unit: The laser beam can be used to identify parts, mainly sheet parts.
Multi-Vision camera: Accelerate recognition by identifying multiple parts at once.
4. Feeding platform (FeederPlate):
Use feeders, bulk feeders and tube feeders (multi-tube feeders) that can be mounted on the front or rear feed platform of the placement machine.
5. Axis configuration
X-axis: The moving head assembly is parallel to the PCB transfer direction.
Y-axis: The moving head assembly is perpendicular to the PCB transfer direction.
Z-axis: Controls the height of the work head assembly.
R-axis: Controls the rotation of the nozzle axis of the working head assembly.
W axis: Adjust the width of the transport rail.
6. Conveying unit
1, the main stopper (Main Stopper)
2, positioning pin (Locate Pins)
3, push unit (in the push component)
4, edge clip (Edge Clamp)
5, Push-up Plate (Push-up Plate)
6, Push-up Pins
7. Entrance plug (inlet plug)
7. Nozzle station: Allows automatic nozzle replacement, a total of 16 nozzles, 7 standard nozzles and 9 optional nozzles.
8. Gas supply unit
Includes air filter, air pressure adjustment button, barometer.


Getting started knowledge


As a high-tech product, the placement machine is safe and correct for both the machine and the personnel.


The most basic thing to safely operate the placement machine is that the operator should make the most accurate judgment. The following basic safety rules should be followed:
1. The machine operator should receive operational training in the correct manner.
2. When checking the machine, replacing parts, or performing maintenance and internal adjustments, turn off the power (you must use the emergency button to service the machine or turn off the power).
3. Make sure to stop the machine at any time using Read Coordinates and YPU (Programming Unit).
4. Make sure that the “interlocking” safety device is always active to stop the machine at any time. Safety tests on the machine cannot be skipped or shorted, otherwise personal or machine safety incidents may occur.
5. Only one operator is allowed to operate one machine during the production process.
6. During operation, certain parts of the body (such as the hands and head) are indeed out of range of machine motion.
7. The machine must be properly grounded (correctly grounded, not neutral).

8. Do not use the machine in a gas or extremely dirty environment.


CONTACT US
YUSH Electronic Technology Co.,Ltd
Contacts:Eva Liu +86 13416743702 / +86 13450659407
Tel:86-0512-62751429
Fax:86-0512-62751429
Website:http://www.vcutpcbdepaneling.com
Email: evaliu@hk-yush.com / sales@yushunli.com
Company Address:3 Building NO 11,Chunhui Road,
Suzhou Industrial Park,Jiangsu Province,China.
Welcome message, we will reply within 24 hours!
Name:
E-mail:
Phone:
Comment:
Copyright @ YUSH Electronic Technology Co.,Ltd.  Views:
*Web site related material and resources are from the Internet, if infringement please inform us, we will remove within 24 hours.*
《中华人民共和国电信与信息服务业务经营许可证》编号:苏ICP备14049770号China.